S3 60Hz
3” submersible multi-impeller pump for 3” or larger wells for pressurization, lifting water from underground, gardening and irrigation activities in residential building service.
Ready-to-use pump.
TECHNICAL DATA
Flow rate: up to 18 GPM
Head up to: 538 feet
Maximum immersion depth: 490 feet
Type of pumped liquid: Clean, free of solids and abrasive substances, non-viscous, non-aggressive, non-crystallized and chemically neutral
Maximum permitted amount of sand: 0.009 lb/ft3 (150 gr/m3)
Liquid temperature: From +32°F to +104°F
Output connection: 1” 1/4 NPT
Pump maximum diameter: 2.91 inches
Impeller/s material: Technopolymer
Maximum number of starts: 20/hour
Protection class: IP68
Motor insulation class: F
Single phase power input: 1x230V(±6%) 60 Hz
Possible type of installation: in vertical position. If it is installed in horizontal position it is necessary to ensure a minimum load on the thrust unit and the cooling sleeve.
Certification: approved to UL, CSA & NSF Standards
CONSTRUCTION FEATURES OF THE PUMP
Technopolymer impellers housed with stainless steel adjustment rings. Pump liner, shaft, coupling with motor, integrated suction filter and cable guard are in stainless steel. Suction and delivery supports in micro-cast AISI 304 stainless steel. Removable built-in non-return valve in technopolymer.
NSF61 certified
CONSTRUCTION FEATURES OF THE MOTOR
Two-pole asynchronous motor completely made of AISI 304 stainless steel.
Two wire version. The thrust block and bushes are cooled and lubricated with a mixture of water and glycol. Rotor mounted on a Kingsbury type self-centering thrust block capable of withstanding high axial loads.
The stator is immersed in thermosetting insulating resin with high heat dissipation capacity and encapsulated in an airtight AISI 304 stainless steel casing.
Removable cable connector CSA approved.
3” submersible multi-impeller pump for 3” or larger wells for pressurization, lifting water from underground, gardening and irrigation activities in residential building service.
Ready-to-use pump.
TECHNICAL DATA
Flow rate: up to 18 GPM
Head up to: 538 feet
Maximum immersion depth: 490 feet
Type of pumped liquid: Clean, free of solids and abrasive substances, non-viscous, non-aggressive, non-crystallized and chemically neutral
Maximum permitted amount of sand: 0.009 lb/ft3 (150 gr/m3)
Liquid temperature: From +32°F to +104°F
Output connection: 1” 1/4 NPT
Pump maximum diameter: 2.91 inches
Impeller/s material: Technopolymer
Maximum number of starts: 20/hour
Protection class: IP68
Motor insulation class: F
Single phase power input: 1x230V(±6%) 60 Hz
Possible type of installation: in vertical position. If it is installed in horizontal position it is necessary to ensure a minimum load on the thrust unit and the cooling sleeve.
Certification: approved to UL, CSA & NSF Standards
CONSTRUCTION FEATURES OF THE PUMP
Technopolymer impellers housed with stainless steel adjustment rings. Pump liner, shaft, coupling with motor, integrated suction filter and cable guard are in stainless steel. Suction and delivery supports in micro-cast AISI 304 stainless steel. Removable built-in non-return valve in technopolymer.
NSF61 certified
CONSTRUCTION FEATURES OF THE MOTOR
Two-pole asynchronous motor completely made of AISI 304 stainless steel.
Two wire version. The thrust block and bushes are cooled and lubricated with a mixture of water and glycol. Rotor mounted on a Kingsbury type self-centering thrust block capable of withstanding high axial loads.
The stator is immersed in thermosetting insulating resin with high heat dissipation capacity and encapsulated in an airtight AISI 304 stainless steel casing.
Removable cable connector CSA approved.
